Solreach All In One ESS(12KW+32KWH)
Solreach All In One ESS(12KW+32KWH)
-
BATTERY CELLS
-
INVERTER
-
WARRANTY
-
Operating Protection
-
Operating Temperature
A-grade Gotion cells
CTVE (Shiyuan)
5 Years
IP54
-10°C~60°C
Description
The Solreach All-in-One ESS 12KW 32KWh is the commercial-grade flagship of the entire Solreach range — the only model with Dual MPPT inputs totalling 14KW of solar charging capacity, a 24KVA surge ceiling, and 98% peak inverter efficiency at 48VDC. Built around a 51.2VDC / 32KWh Grade-A Gotion LiFePO₄ battery pack delivering 28.8KWh usable at 90% DoD, it is engineered for applications where a single ESS must power an entire facility: commercial buildings, agricultural processing units, remote telecom clusters, and micro-utility microgrids.
Core Product Advantages
Dual MPPT — 14KW total solar intake, split-array optimisation
-
Two independent MPPT channels: 27A × 2 / 9KW primary + 22.5A / 5KW secondary — no combiner box needed for two-string arrays
-
Each channel tracks its own IV curve, eliminating inter-string mismatch loss caused by shading or orientation differences
-
Total 14KW PV input is the highest of any Solreach ESS model — enough to fully recharge the 32KWh battery in under 3 hours at peak irradiance
98% peak efficiency — the highest in the Solreach ESS range
-
98%@48VDC in battery mode — 4 percentage points above the 6.5KW model's 94%, recovering up to 1.3KWh more per 32KWh cycle
-
At fleet scale (20 units × 28.8KWh/day), 98% efficiency saves an estimated 8,000–10,000KWh annually versus 94% alternatives
-
Lower thermal dissipation per cycle also extends inverter component lifespan, reducing OEM after-sales service burden
Industrial multi-protocol communication — SCADA, AMF, and generator-ready
-
RS485 + RS232 + USB + Dry Contact: the only Solreach ESS with four concurrent communication interfaces for industrial integration
-
Dry Contact output enables direct AMF (Automatic Mains Failure) signalling to diesel generators — no additional relay module required
-
RS485 Modbus RTU support allows integration into SCADA, building energy management systems (BEMS), and multi-inverter monitoring platforms
Specifications Parameter
Output Voltage Waveform
Rated AC Output Power
Rated AC Output Power
Rated AC Output Power
Rated AC Output Power
Output Voltage
Output Voltage
Output Voltage
Output Voltage
Low DC Warning Point
Low DC Warning Point
Low DC Warning Point
Low DC Warning Point
Low DC Warning Point
Low DC Warning Point
Low DC Cut -off Voltage
Surge Power (kVA)
Surge Power (kVA)
Voltage (VAC)
Voltage (VAC)
Voltage (VAC)
Power Factor (PF)
Power Factor (PF)
Rated Capacity (kW)
AC Input
Rated Input Voltage (VAC)
220/230/240; L+ N +PE
Voltage Range (VAC)
90~280+3 (normal mode); 170~280+3 (UPS mode)
Frequency (Hz)
50Hz / 60Hz (Auto Detection)
AC Output
Rated Capacity (W)
12000W
Surge Power (kVA)
24
Voltage (VAC)
220/230/240
Power Factor (PF)
1
Frequency (Hz)
50/60Hz+0.1%
Switch Time (ms)
10 (APP/UPS mode);20 (GEN mode)
Wave Form
Pure Sine Wave
Overload Capacity
110% < load < 125%) 5%: report error and turn off the output after 10 seconds;
Load >125% 5%: report error and turn off the output after 5 seconds
Charger (PV+AC)
Solar Charger Type
Dual MPPTs
Max PV Input current /power
1*MPPT:27A/9KW,2*MPPTs:22.5A/15kW
Operating Voltage Range (VDC)
90~485
Max PV Open Circuit Voltage (VDC)
500
Max PV Charge Voltage (A)
160
Max AC Charge Current (A)
160
Max. Charge Current (PV + AC)(A)
160
Battery
Nominal Battery Voltage
51.2VDC
Rated Energy
32KWh (0.5C,25°C)
Usable Enerqy (90% DOD)
29kwh
Max. Charge/Discharge Current
200A/200A
Operation Voltage Range
44.8vdc~58.4Vdc
Operation Temperature
-10°C~+60°C
Intertace
revea
LCD
communication
RS485/ RS232/USB / Dry Contact
Monitoring
WIFI
General Protection
Operating Protection
IP54
Operating Temperature
-10°C~60°C
Relative Humidity
5% ~ 95% (Non-condensing)
Storage Temperature
-15°C~60°C
Max Operating Altitude
4000m (Derating above 1000m)
Dimension
LxWxH (products size, mm)
695*295*1545mm
LxWxH (package size, mm)
855*480*1630mm
Weight(NW Kg)
267Kg
Weight(GW Kg)
295Kg
常见问题
问：镀锡铜 PV1-F 4mm2 太阳能电缆中的 PV1-F 额定值与其他太阳能电缆额定值有何区别？
答：PV1-F 是用于光伏系统的特定等级，意味着电缆已经过测试和认证，符合太阳能电池板系统的国际标准。其他额定值则可能没有经过专门测试用于太阳能电池板系统。
问：如何判断镀锡铜 PV1-F 4mm2 太阳能电缆是否适合我的太阳能电池板系统？
答：您可以通过咨询持证电工或太阳能电池板系统制造商来确定镀锡铜 PV1-F 4mm2 太阳能电缆是否适合您的太阳能电池板系统。他们将为您推荐最适合您特定需求的电缆。
